Secondhand EVs, Marine Parts & Garbage Trucks: A Procurement Manager's Honest TCO FAQ

Tuesday 3rd of November 2026By Charlotte Avery

I've managed our fleet and equipment procurement budget for seven years now. In that time I've handled about $2.4 million in cumulative spending, negotiated with 30-plus vendors, and logged every order in our cost tracking system. Here are the questions I wish someone had answered for me in my first 18 months — back when I was still learning TCO the hard way.

Are pre-owned Volvo electric SUVs actually worth it for a fleet?

Start with battery health data, because "used EV" makes everyone nervous. According to Recurrent's published fleet data, a typical EV at year three still holds roughly 85%–90% of its original range. If you're running 15,000–20,000 miles a year on predictable urban and suburban routes, that's usually workable.

Do the math. A three-year-old EX90 or XC40 Recharge typically prices 35%–45% below the same model new. That's real money. But you need three things before you sign: (a) an independent battery health report, (b) the charging history (fast-charge vs. trickle), and (c) written confirmation that the battery warranty transfers. Miss one and the "discount" can evaporate.

I learned that the hard way in 2024. The seller's battery report showed 89% health — "very good." What I didn't ask: tested under what charging conditions? Turns out it was a 20%–80% depth-of-discharge test. Our fleet charges to 100% overnight. Real usable range was closer to 77% of original. I should have asked about test conditions. I didn't. Cost us about $6,000 in range-adjusted value when we resold that vehicle 14 months later.

This worked for us because we have fixed depot charging and predictable routes. If you're running long-haul or lack overnight charging infrastructure, the calculus is completely different. Your mileage may vary — literally.

Volvo Penta marine parts: Can aftermarket savings actually stick?

My honest answer: for critical marine engine components, aftermarket "savings" often get eaten by downstream costs. The working environment is harsher than land-based — salt, constant load, long cooling paths. OEM tolerances exist for a reason.

We logged a specific case: an aftermarket impeller ran about 40% cheaper than OEM. But its replacement interval in saltwater was roughly 30% shorter, and when it failed, the fragments damaged the pump housing. Repair bill: $2,800. The OEM part difference? About $180. You can do the rest of the math.

That said, not every part needs OEM. Filters and belts — standardized, low-risk — aftermarket is fine. Impellers, seals, sensors — stick with OEM. This applies to our usage pattern, which is 200–300 operating hours per year. If you're running much higher hours, the replacement interval math shifts, and OEM actually gets more cost-effective, not less.

Garbage trucks: What's the most overlooked lifetime cost?

Most buyers price three things: the chassis, fuel, and routine maintenance. That's roughly 60%–65% of the real number. The other 35%–40% hides in three places.

First, the hydraulic system. Packing, lifting, and compaction run on hydraulics. A residential route might cycle 800–1,200 stops a day. Hydraulic oil and seal degradation accelerates well beyond a standard truck. Budget for it from year one, not year three.

Second, downtime. A garbage truck down means a whole route is disrupted. When we modeled it, a single vehicle down for one day plus re-routing and a rental covered around $800–$1,500 in combined operational impact. That number never shows up in a purchase quote, but it's real.

Third, body-to-chassis integration. The fit between the refuse body and the chassis varies a lot by build. Poor integration accelerates rear suspension and PTO wear. I ask for the manufacturer's integration specs in writing before comparing final prices. A $4,000 cheaper bid can cost you far more over five years.

Mustang trucks and compact equipment: What should buyers actually compare?

Compact equipment — skid steers, track loaders — has a "looks about the same on paper" problem. Mustang, Bobcat, and similar brands post similar specs, but real-world operating costs diverge. I break comparisons into four dimensions:

  • Hydraulic flow and attachment compatibility. Determines whether you can take on additional work without a second machine.
  • Service access. Can a tech reach the key components without lifting the cab? This matters enormously on used units.
  • Parts commonality. Some brands' proprietary parts run 3–5x the cost of shared components.
  • Resale value. Three-year residual varies noticeably. Mainstream names hold value better for a reason.

If you're using compact equipment under roughly 400 hours a year, leasing usually beats buying on TCO. I've run this comparison honestly multiple times — rental wins until you hit high utilization or need highly customized attachments. Below that threshold, your money goes further renting.

What does "Are You Smarter Than a 3rd Grader" have to do with equipment buying?

It sounds like a joke, but I treat it as a serious filter: the basic-science test.

Almost every equipment mistake I've made — or watched someone else make — could have been caught with a third-grade-science-level question:

  • What duty cycle is this machine rated for — continuous or intermittent?
  • What's the cooling system's operating range at ambient extremes?
  • Is hydraulic oil change based on hours or calendar time — and what happens if those disagree?

I once almost signed a contract that looked great on paper. Then I asked: "What's the transmission oil temp limit under full load on a grade?" The vendor got quiet. The spec sheet didn't say. When I pulled the technical manual, that operating condition sat right at the thermal limit. Third-grade science: heat plus load equals wear. That question saved us from a $28,000 mistake.

My rule now: any equipment purchase over $20,000 requires answering three basic physics/engineering questions before signing. If we can't answer them, we go back and do more homework. This habit has saved more money than any spreadsheet comparison I've ever built.

So when is "cheap" actually expensive?

In our records, the lowest quote ended up with the highest total cost in about 60% of cases. Usually through hidden fees, shorter replacement cycles, higher failure rates, or downtime.

But here's the boundary: if usage is light, replacement cost is low, and the consequence of failure is manageable, then cheaper and lower-quality is absolutely fine. Not everything needs to be premium. The point is to calculate what "cheap" and "expensive" actually mean in your specific operating context — before you sign, not after.

Procurement isn't about finding the lowest price. It's about finding the lowest total cost for your actual usage pattern. Those two things are frequently not the same number.

Have a Processing Question?

Our application engineers answer crusher and screen selection questions at no charge.

Ask an Expert